Home
home products support company info   view cart
Up

 

Material on this website:  copyright 1997-2010. It may be printed for your personal use but may not be used for commercial purposes, copied, or altered and posted on other websites

Array Solutions

Phone
(214) 954-7140
Fax
(214) 954-7142

Email Us

ARRAY SOLUTIONS BROAD BAND ANTENNAS

No tuner broad band antennas, perfect for ALE and spread spectrum, and more efficient then T2FD type antennas!

                               1/2 of packaged antenna                                                                     Close-up of rugged termination  load (no PVC tube)

AS-BB-175 model shown in detail below

Quality Components Means Assured Reliability

1      User supplied 3/8-1/4” suspension rope, black Dacron® recommended.                 

2      2.5” glazed ceramic stress insulator. 

3      1/8” double-braided black Dacron® UV, chemical resistant rope.                           

4      13AWG insulated copper-clad steel wire w/mil-spec black PE insulation. 

5      Spreaders are pultruded fiberglass tubing, 36” x 1.5” OD x 1/8” wall, reinforced at all points where wire elements pass with 5” x 1.25” OD x 1/8” wall fiberglass inserts for added strength in these high stress areas.  All electrical connections are hand-soldered, fully stress-relieved and/or epoxy potted within the spreaders. 

6      All connections and junctions between spreaders and wire elements are stress-relieved, using our exclusive combination of 1/8” double-braided Dacron rope and machine-swaged, twin-cavity aluminum crimps.  This method provides great strength and prevents any movement that would result in ware and possible failure of these vital mechanical junctions under full load conditions of wind and snow. 

7      Hand-built and fully tested, “true” balun is designed for continuous-duty at full rated power.  Each is housed in a NEMA 4” x 4” marine-grade enclosure, mounted on a ¼” thick black UHMW-PE mounting plate with all stainless-steel hardware.  2” stainless U-bolts are provided for mast-mounting of antennas in inverted-V configuration if desired.  Standard coaxial connector is type-N, with others available at additional cost.  Full stress-relief for this connector is provided, the coaxial feed-line is not.  Feed-point impedance is 50 ohms nominal. 

8      Twin loads are non-inductive and housed in 12” OR 10” x 2” OD x 1/8” wall fiberglass tubes with heavy, epoxy-sealed polystyrene end-caps.  All hardware is stainless-steel and brass.  Full strain-relief is provided by uniquely designed suspension bridles comprised of 1/8” double-braided black Dacron® rope, 1” polypropylene webbing and mil-spec black polymer hardware.  All connections are made using machine-sledged aluminum crimps.       

No PVC, or other small tubes or UV unstable parts! No other manufacturer makes anything as rugged as these broad band models!

 

Specifications:   AS-BB-Series

Power Handling

Two models, 500 W CW/1 KW PEP and 1.5KW CW/3 KW PEP

Length

90 and 175 foot models 

Weight

90 foot 26 lbs   /   175ft  33 lbs

Bands

90 foot 3-180 MHz  and 175 foot 1 to 180 MHz

Balun model AS-800

True 16:1 balun, warranted for life. (direct lightning strike EXCLUDED. See our warranty policy for details) NEMA 4X rated!  No PVC plumbing pipe used ANYWHERE!

Wire

13AWG flexible stranded copper-clad steel with very heavy, black mil-spec PE Insulation. Other types such as stainless-steel cable, insulated and non-insulated available at additional cost on special order.   

Build Quality

Built to meet or exceed Mil-Specs for wire antennas. All hardware is stainless steel, most with black oxide coating. Baluns are warranted for life!   130 MPH Rating EIA-TIA-222-G

Mounting Options

May be suspended from halyards, or mast mounted.  Mounting as a flat-top or inverted-V

Shopping Cart - price list - Agencies Call or email your RFQ

SWR and Return Loss Plots .5 to 30 MHz

SWR and Return Loss .5 MHz to 170 MHz

Shopping Cart - price list - Agencies Call or email your RFQ